The first circle we cut fell apart along the edge. Half the boards on the curve had lost the stringer under them and flapped like loose piano keys.
You’ll also love: How to Turn Broken Plates into a Mosaic Patio Table, How to Build a Gabion Fire Pit Grill from an Old Car Wheel, How to Build a Tilted Pot Flower Tower on a Wire Obelisk.
Our pallet swing bed is a 6-foot round platform cut from four pallets, with a low wall of pallet halves around the back, hung on chains from a timber frame 9 feet tall.
The second circle got 2×4 cleats underneath before the saw came out. Nothing flapped.
A neighbor tried it first, swung twice, and said it felt like a boat, which she didn’t mean as a compliment. The chains tick against the eye bolts on every swing.

What Keeps a Hanging Bed Steady
We expected the bed to tip when someone sat on the edge. It leans a few degrees and stops, because the two chains on each side meet high overhead, and the higher they meet, the less it leans.
The frame carries more than the bed. With two adults aboard, the hangers hold around 650 pounds, and a good swing adds to that for a moment at the bottom of each arc.
Pallet wood is hard, dry and full of old nails. It splits if you screw too close to an end.
Materials & Tools
Not in the $720: cushions, lights, flowers and lanterns, plus the jigsaw, drill, post-hole digger and bolt cutters.
The stamp: HT means heat-treated, which is what you want. Skip pallets marked MB, for methyl bromide, and any with no stamp at all.
S-hooks: an open hook can slowly straighten under a swinging load. Every link between beam and bed should be closed and rated.
Under it: feet drag under a swing bed and wear the grass to mud. A 7-foot patch of gravel, laid the way we did our white gravel garden path, holds up better.
Watch the Build
Step by Step
Step 1Pick the pallets
Choose six pallets with every board and stringer sound, stamped HT. Pry off any cracked boards and sand the tops with 80-grit so nobody lies down on a splinter.

Step 2Join four into a square
Lay four pallets deck-up in a block 80 × 96 inches. Screw 2×4 cleats across every joint underneath, three screws into each pallet, so the board ends along the curve will have something to hold them.

Step 3Cut the circle
Drive a screw at the center, tie a string to it, and draw a 72-inch circle with a pencil held 36 inches out. Cut along the line with a jigsaw.
Use a demolition blade. Old pallet nails strip the teeth off a wood blade in seconds.

Step 4Add the hanger beams
Flip the circle over and screw two 2×6s across the underside, front to back, 24 inches either side of center; each one is about 54 inches long. Drill a ½-inch eye bolt up through each end, eye on top of the deck, with a washer and nut underneath.

Step 5Build the back wall
Cut two more pallets lengthwise into 48 × 20 inch panels and add a 2×4 along any cut edge that lost its stringer. Stand three of them around the back of the circle, leaving about 5 feet open at the front.
Screw a 2×4 upright behind each joint, running down the side of the platform, so leaning back can’t fold the wall over.

Step 6Raise the frame
Dig two holes 12 inches wide and 36 inches deep, 8 feet apart inside to inside, with 6 inches of gravel at the bottom of each. Set the 12-foot 6×6s plumb with three bags of concrete apiece and leave them a week.
Set the 10-foot 6×6 across the tops in steel post caps, bolt it down, and bolt a 24-inch 4×4 brace across each top corner at 45°. Where frost goes deeper than 3 feet, so do the holes.

Step 7Hang it and test it
Through-bolt the swing hangers to the beam, 48 inches apart and centered. From each one, run two chains with quick links down to the front and back eye bolts on that side, and adjust a link at a time until the platform hangs level, 18 inches off the ground.
Before anyone gets in, stack about 400 pounds of bagged sand on it and leave it overnight. Check every bolt and link in the morning.

Step 8Prime and paint
Brush exterior primer over the bed and frame, working it into the gaps between slats. Follow with two coats of white exterior paint.

Step 9Add the lights
Stick an outdoor LED strip down the inside face of each post and plug it into an outdoor-rated outlet. String lights along the beam finish it.

Step 10Dress the pallet swing bed
A round outdoor cushion about 70 inches across fills the platform inside the wall. Line the wall with back pillows and set two lanterns on the grass in front.

How the Pallet Swing Bed Holds Up
Chain links wear where they rub the eye bolts, so that’s where to look each spring. Replace any link that has worn noticeably thinner than the rest; a ¼-inch grade 30 chain is rated for 1,300 pounds new, not worn.
Pallet wood checks and splinters in sun and rain. Sand the rough spots and repaint every couple of years.
FAQ
The bed hangs crooked
One side’s chains are longer than the other’s. Move the quick links a link at a time, side to side first, then front to back.
The frame wobbles when we swing
Check the brace bolts and the post caps first; one loose bolt makes the whole frame sway. If the posts move at the ground, the holes are too shallow for your soil, and the only real fix is digging them deeper.
I can’t find heat-treated pallets
Build the platform from 2×6 deck boards screwed to a frame of 2×6s instead. It weighs more and costs more, but every board is sound.
Can I hang it from a tree?
We haven’t hung one from a tree. A limb’s strength is hard to judge from the ground, and this bed with two people on it weighs about 650 pounds.
Does it come in for winter?
The frame and platform stay out. Cushions, pillows and the LED strip go into the shed, and the chains get a close look before spring.
The neighbor came back the next week with a seasickness wristband, as a joke. It still hangs on the frame, next to the lantern hook.









