How to Turn Broken Plates into a Mosaic Patio Table

This post contains affiliate links. As an Amazon Associate I earn from qualifying purchases. Read the full disclosure.

Spreading mortar straight onto the wooden slats was the first plan. A test patch cracked along every gap between the boards within a week, as the wood swelled and shrank under it.

You’ll also love: How to Build a Gabion Fire Pit Grill from an Old Car Wheel, How to Make Concrete Mushroom Garden Stakes in Eggshells, How to Make Concrete Leaf Stepping Stones for a Garden Path.

Our mosaic patio table sits on a 36-inch circle of cement board instead, screwed to the slats, with 16 thrift-store plates set into a thin bed of thinset.

A plate under a towel gives one dull crack, then sounds like ice in a glass when you lift the towel.

A friend recognized one of the blue plates as hers. She decided she liked it better this way, eventually.

Finished mosaic patio table with blue, teal, orange and white plate shards in white grout

Project at a glance

Active time
About 6 hours over 4 days
Cure time
1 day to grout, 3 more to seal
Cost
About $110
Difficulty
Moderate
Finished size
36 in round top

What the Cement Board Does Under the Plates

Cement board doesn’t swell when it gets wet the way wood does. Screwed down every 6 inches, it gives the thinset a flat, stiff base that stays put under the shards.

We expected the curved plate rims to be a problem on a flat top. They break into pieces that tip, so those went around the edge and the flat centers went into the middle.

Dark blue looks darker once it’s grouted. White joints make every color stronger.

Materials & Tools

Round patio table with a slatted top1, 36 in across
Cement backer board, ½ in1 sheet, 3 × 5 ft — the 36-in circle just fits
Cement board screws, 1¼ in1 small box — about 30 screws
Check on Amazon
Polymer-modified thinset, exterior rated1 bag, 25 lb
Dinner plates16, porcelain or stoneware, about 10½ in
Sanded grout, white1 box, 10 lb
Tile nippers and a rubber mallet1 of each
Check on Amazon
Grout float and grout sponge1 of each
Check on Amazon
Penetrating grout sealer1 bottle — two coats
Check on Amazon
Safety glasses and gloves1 pair each — shards fly, thinset burns
Check on Amazon

Not in the $110: the table, the mallet and the jigsaw that cuts the board.

Planning colors: lay the dry shards out on the bare board first, ring by ring, and take a photo. Once the thinset goes on, the photo is the plan.

Which plates: porcelain and stoneware hold up outdoors. Soft earthenware, the kind with a chalky unglazed ring underneath that drinks a drop of water, cracks the first winter it stays wet.

A smaller version: the same shards and grout cover a concrete planter rim nicely; the flat sides of our concrete outdoor sink would take them too.

Watch the Build

Step by Step

Step 1Screw down a cement board circle

Mark a 36-inch circle on the board with a string and pencil and cut it with a jigsaw and a carbide-grit blade, outdoors with a dust mask on. Lay a zigzag of exterior construction adhesive on the slats, set the circle on top and drive a cement board screw every 6 inches into the slats below.

Sand the old finish off the slats with 80-grit first, so the adhesive grips bare wood.

Round slatted wooden patio table before the mosaic top goes on

Step 2Spread the thinset

Mix the thinset to a peanut-butter stiffness and spread it ⅛ inch thick with the flat of the trowel. Do one third of the top at a time; thinset skins over in about half an hour, and shards won’t stick to a skin.

Spreading gray thinset across the round table top with a trowel

Step 3Break the plates

Fold a plate inside an old towel, flat on a hard surface, and hit the center once with the mallet. Two or three more taps break the pieces down to 1 to 2 inches; tile nippers trim the odd shapes.

Glasses on. Shards come out of the towel edges. Sort the pieces into bowls by color as you go, which makes planning rings far easier than picking from one pile.

Breaking a ceramic plate with a mallet on a towel to make mosaic shards

Step 4Set the outer ring

Start at the rim with the curved edge pieces, glaze up, pressed into the thinset with a thumb. Leave gaps of ⅛ to ¼ inch between pieces for grout.

A curved piece sits flat if you butter its back with a little extra thinset before pressing it in.

Setting the first ring of blue and white shards around the edge of the mosaic patio table

Step 5Work toward the center

Lay rings of color inward, keeping the flattest pieces for the middle where cups and plates sit. Spread the next third of thinset only when the last one is covered.

Rings of blue, teal and white shards filling in toward the table center

Step 6Tap them level

Lay a scrap of flat board across a patch of shards and tap it with the mallet so the tops line up. A shard standing proud catches every glass set down on it.

Leave it a full day before grouting.

Tapping the mosaic shards level with a red rubber mallet

Step 7Grout it

Mix the sanded grout stiff (Mapei’s sanded grout is made for joints from ⅛ to ⅝ inch, which covers every gap here), pile it on the top and push it into the joints with the float held at 45 degrees, working diagonally across the gaps. Scrape the extra off with the float’s edge.

Pushing white grout into the mosaic joints with a blue grout float

Step 8Wipe it clean and seal

After 15 to 20 minutes, wipe in circles with a damp sponge, rinsing it often, until the glaze shows through the haze; wring the sponge nearly dry, since a wet one pulls grout back out of the joints. Buff the last film off with a dry cloth an hour later.

Give the grout 3 days, then brush two coats of penetrating sealer over the whole top.

Sponging the grout haze off the shards to reveal the blue and orange glaze

How a Mosaic Patio Table Holds Up

Water is the enemy, not wear. Seal it again every spring, and cover it or bring it in before a hard freeze; a top that freezes wet can pop shards loose.

The white grout darkens around the center first, where coffee cups land.

FAQ

Some shards are sharp at the edges

The broken edges of a plate are as sharp as glass. Run a rubbing stone or a sanding sponge along any that stand above the grout, and fill low spots with a little more grout.

A piece came loose after grouting

It was set into thinset that had already skinned over. Chip out the old grout around it, butter the back with fresh thinset, press it in and grout the gap the next day.

Can I use floor tile instead of plates?

Yes, and porcelain tile is flatter and tougher than most plates. Break it the same way; it just takes a harder hit.

The grout cracked in a line across the top

That’s usually the board flexing between screws. Check that every screw bit into a slat, and add screws where the board gives under your hand.

How heavy does the table get?

The board, thinset, plates and grout add roughly 45 pounds. We haven’t weighed a full table, base and all.

The friend’s blue plate is in the outer ring, three pieces in from the edge nearest the house.

She points it out to everyone who sits there.

You Might Also Love

Owen Carter

I write the guides on Canonigos. Every project comes with its video, a materials list and the measurements you need to build it yourself.

Leave a Comment